VLPK-2G for Gibsons

Put some warmth and classic tone in your guitar! More body, fuller tone and letting the subtleties of your pickups come through; that is what to expect with the BCS Vintage. This kit is a core electrical replacement for any Gibson Les Paul or LP copy with a thick arch top that uses long shaft pots. To know if your guitar needs the long shaft pots you will need to remove one of your original pots and measure the bushing (the threaded part of the shaft). If the bushing is 3/4″ (19.05mm) long then your guitar takes the long shafts, if it is 3/8″ (9.53mm) long you will need the short shafts so see our VLPK-2 kit.

50’s Wiring: This kit is wired to a 1950’s Gibson Les Paul wiring schematic. With the 50’s wiring the overall tone gets stronger and more transparent, meaning the notes seem to “open up” more. Another benefit is the loss of treble when rolling back the volume is reduced considerably and a volume mod, or treble bleed mod, would only improve this slightly.

We use only high grade components in our kits to bring out optimum performance.

Bourns Potentiometers: The VLPK-1 uses 500K Bourns Pro Audio Guitar, Long-split shaft pots with an Audio taper and a low torque (which means these pots turn VERY easily). We chose the Bourns pots because we found them to have a superior taper over the CTS pots we used to use. These pots have an 18 spline shaft so your U.S. spec knobs will not fit without first pinching the top of the split shaft together and then slowly push them on. Import knobs will fit fine. If your guitar is an actual Gibson then your new pots should fit in the pot holes of your guitar just fine, but if it is a copy or another brand guitar that is using a long shaft pot your volume and tone pot holes may not be not 3/8″ in diameter, if so you will need to open them up for the new pots to fit. Don’t worry this is easier than it sounds and a step by step is included in the instructions.

Capacitors: Oil filled capacitors have a much smoother, more natural sound than the standard ceramic capacitors. While they sound better, they usually cost a lot more as well, but a higher price does not guarantee a better capacitor. After having used a different capacitor brand for several years we switched to the WD Tone Cap due to their superior performance while remaining reasonably priced. We found them to have a very smooth, organic tone and when turning down the tone knob they sounded more musical and less like a blanket being thrown over the amplifier. The WD Tone Caps use oil soaked mylar as the di-electric material (as do most “paper-in-oil” capacitors do these days) and they are kept to a ±10% tolerance. These capacitors are manufactured by Taihan, the same company that manufactured the Vitamin Q capacitors sold by ALLPARTS for years and the Black Bees capacitors that are currently offered (both mylar and oil caps). The WD Tone Caps are essentially the same capacitor as the Black Bees but at 600v instead of 1500v and with tighter tolerances. These capacitors will give you that warm, vintage tone you’re looking for without paying a ridiculous amount of money. The current pictures still show the Vitamin T capacitors, we will be uploading new photos with the WD Tone Caps soon.

Wire: For the Vintage series we use vintage accurate cloth covered wire that is encased in a braided outer shielding. This is the same type of 22 gauge thick stranded wire that was commonly used in the Gibson guitars of the 50’s and 60’s. Today most everyone else uses 24 to 26 gauge thin stranded wire in their guitars and that theoretically it gives you more electrical transfer because of the higher number of strands, but we have found that the higher gauge thick stranded wire (therefore fewer strands) lowers the resistance and changes the inductance which results in a more detailed tone. The electrical differences are very small but they are cumulative with the enhancements provided by the other components which results in a superior tone.

Click the links below to see the Installation instructions and our schematics so you will know what is involved in installing one of these kits.

Vintage LP Basic Installation Instructions

Vintage LP Wiring Schematic

Make Sure it Fits: Here are the measurements of our kits control layout. All measurements are from center to center. There is about 1/4″ (6.35mm) of slack between each of the components so the measurements can be close and the kit can still fit if it is within the amount of slack mentioned above. 

  • Neck Volume to Neck Tone:         2 1/2” or 63.5mm
  • Neck Volume to Bridge Volume:   2 1/8” or 53.97mm
  • Bridge Volume to Bridge Tone:    2 1/2” or 63.5mm
  • Bridge Tone to Neck Tone:          2” or 50.8mm
  • Bridge Tone to Output Jack:        1 3/4” or 44.45mm

Assembled kit includes:

  • 4 – 500K Bourns Pro Audio Guitar, long split shaft pots with a low torque (18 Spline)
  • 2 – Russian K40N .022uf/400v paper-in-oil capacitors for a warm vintage tone
  • All shielded 22 gauge thick stranded wire (vintage accurate)
  • Assembly template



Turn Around Time

Due to the expansion of our customer base, our turnaround times are 3 to 5 weeks from the time you order. We have recently picked up two guitar manufacturers that we are building wiring harnesses for, and the word of mouth about the quality of our work and customer service has expanded our customer base tremendously. Each kit is built to order, and in the order it was received. It will take some time for you to receive your kit, but it will be well worth the wait, guaranteed! - Bill Brown/owner BCS Guitars.

Warning: Unknown: open(/home/content/32/4220432/tmp/sess_vaq1ptinamqejk4mmg0mngab06, O_RDWR) failed: No such file or directory (2) in Unknown on line 0

Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct () in Unknown on line 0